Boots Long Hot Water Bottle
In order to buy non-prescription medicines you must be a registered user of our site as we are obliged to record your transaction history. We also ask that you complete our questionnaire so our pharmacy team can check that this product is suitable for you to buy.
Disabled or chronically sick people can claim VAT relief on purchases for personal or domestic use that are applicable to their disability or sickness.
Check store stock overlay
Product details
Boots Long Hot Water Bottle with knitted cover. Helps keep you warm & cosy.
Dimensions:
2.7ltr capacity
79cm long, 12cm wide
Suitable for
Not suitable for infants or persons insensitive to heat.
How to use
For your safety and in order to obtain the maximum life from your hot water bottle please read these instructions carefully before use. If there is a possibility that prolonged contact with the skin could occur, an adequate cover should be used to prevent burns. This hot water bottle is LATEX FREE amd is made of phthalate free PVC. This product is suitable for latex allergy sufferers.
This hot water bottle is designed for partial filling only. When filling this hot water bottle do not use boiling water. Do not fill using water from the domestic hot water system as this can considerably shorten the life of the hot water bottle.
-
Fill to a maximum of two thirds capacity or less. Do not overfill as this might cause the hot water bottle to burst. Hold the hot water bottle by the neck in an upright position and fill slowly to avoid hot water splashing back.
-
Expel air by lowering carefully onto a flat surface until water appears at the opening.
-
Screw the stopper sufficiently tight, in practise finger tight should be adequate.
-
Finally, make sure the funnel is empty.
Additional instructions on how to tighten the Boots hot water bottle stopper correctly
It has become apparent that a small number of users have experienced leaks during use of the Boots hot water bottle. We would like to reassure our customers that all our bottles are individually tested for faults and conform to the current British Standard 1970:2012, which is the global safety standard for hot water bottles.
To prevent the hot water bottle leaking during use it important that the stopper is tightened correctly. To close the stopper sufficiently tight the stopper should be turned until it cannot be turned further without the use of excessive force. Failure to do this can result in leaking from the stopper area during use.
How to tighten the stopper correctly
When the stopper is in position it reaches its biting point and the resistance on turning increases. At this point the stopper should not be considered sufficiently tight as it can leak during use. To secure the stopper properly to prevent leaks it is necessary to tighten the stopper until it comes to a complete stop and cannot be turned further without the use of excessive force.
Under no circumstances should the hot water be used as a cushion or sat on. Prevent contact with hot surfaces. Prevent contact with oil or grease. When not in use, drain completely and keep, with the stopper removed, in a cool, dry, dark place. Prevent exposure to sunlight. Do not place anything on top of the hot water bottle during storage. Check the hot water bottle and stopper for wear and damage prior to use. Check the hot water bottle for any leakage by holding it in an upside down position. Do not microwave this hot water bottle. It is recommended that boiled water is left to cool for at least 5 minutes before filling your hot water bottle.
Hazards and Cautions
Hot water bottles are no suitable for use with infants or persons insensitive to heat. Please be aware that sensivity to heat can be impaired by overtiredness, certain medicines, alcohol or illness. It is strongly recommended that children are supervised when using hot water bottles.
For young children and those with sensitive skin, it is recommended that you do not fill the hot water bottle with water that is above 40C/104F and ALWAYS use a cover with the hot water bottle.
Important info
It is recommended you replace your hot water bottle at least every 2 years. Please keep these instructions for future reference. This hot water bottle is LATEX FREE and is made of phthalate free PVC. It is manufactured to BS:1970:2012 and holds a 2 year guarantee against manufacturing faults only. THIS GUARANTEE DOES NOT AFFECT YOUR STATUTORY RIGHTS.
